Toilet Repair & Installation in Hollywood, FL
Toilet repair and installation in Hollywood, FL covers running toilets, leaks at the base, weak flushes and full replacements. Call (954) 697-4920 for a repair or replacement plan, with the price stated first.
- Repair or replace advice
- Water-saving models
- Price before work
Diagnosis
What Your Toilet Is Telling You
| Symptom | Likely cause | Typical fix |
|---|---|---|
| Runs on or hisses | Worn flapper or fill valve | Replace the part |
| Water at the base | Failed wax ring or loose bolts | Reset the toilet with a new seal |
| Weak or incomplete flush | Clogged rim jets, low tank water, partial clog | Clear the jets and adjust the water level |
| Rocks or wobbles | Loose closet bolts or a damaged flange | Re-secure or repair the flange |
| Tank sweats or drips | Humidity on a cold tank | Anti-sweat liner or a mixing valve |
| Gurgles when other fixtures drain | Venting or main line issue | Camera and drain service |
Water and Money
A Running Toilet Is Quietly Expensive
The EPA says a leaking toilet can waste about 200 gallons a day. At a combined Hollywood water and sewer rate of roughly $15.59 per extra 1,000 gallons, according to one rate calculator, that is close to $90 a month.
Rates are rising through 2031 under the city's plan, so the same leak costs more each year. A fifteen-dollar flapper beats a bill like that every time.
If you are unsure whether a toilet is the source of a rising bill, the dye test works. Put a few drops of food coloring in the tank without flushing, wait fifteen minutes and look for color in the bowl.
Toilet overflowing right now?
Close the supply valve and call. Overflows get priority.
Replacement
When a New Toilet Pays for Itself
Older toilets use far more water. The EPA says WaterSense-labeled toilets use 1.28 gallons per flush or less, while older models can use 3.5 gallons or more. A household that flushes thirty times a day saves real money on water and sewer charges with a modern model.
Replacement is also the answer for a cracked bowl, a failing glaze or a toilet that has needed three repairs in two years. Taller comfort-height models and elongated bowls are options, and the rough-in distance decides what fits.
Installation
How a Toilet Replacement Goes
- 1
Shut off
Close the supply and drain the tank.
- 2
Remove
Lift the old toilet and clean the flange.
- 3
Seal
Set a new wax or waxless seal.
- 4
Set and test
Secure, connect, flush and check for leaks.
Often Overlooked
Check the Flange Before You Blame the Toilet
- The flange should sit level and firmly secured to the floor.
- A cracked or rusted flange lets the toilet rock and leak.
- Floor height changes after new tile can leave the flange too low.
- A soft floor around the toilet means water has been leaking for a while.
- Fixing the flange and subfloor first prevents a repeat leak.
Local Notes
Condos, Older Homes and Septic Tanks
Condo owners should check whether the building requires notice or a certificate before work, and remember that a leak at a toilet can reach the unit below. Older Hollywood houses may have cast iron drains that make a toilet reset trickier.
About 44 percent of Hollywood relies on septic tanks, so what goes down the toilet matters. If a leak under the toilet has been running for a long time, electronic leak detection checks for damage elsewhere. Our Pembroke Pines page covers the mix of older and newer homes there.
Around Hollywood
Toilet Repairs in Hollywood Rentals and Homes
Short-term rentals near Hollywood Beach put heavy use on toilets, and a rocking base or a running flapper shows up quickly. Homes in Hillcrest and Hollywood Lakes more often need a wax ring or a fill valve after years of service.
Close the supply valve at the wall when a toilet overflows, then call. A valve that will not turn is its own repair.
Pricing
What Shapes the Price of Toilet Work
Planned installs get a free estimate. Call (954) 697-4920 and describe what the toilet is doing.
Questions
Toilet Repair Questions
The usual cause is a worn flapper or a fill valve that does not shut off. Both are inexpensive parts. A running toilet can waste about 200 gallons a day, according to the EPA, so it is worth fixing promptly.
Water around the base, a rocking toilet, a sewage smell or a soft floor near the toilet are the signs. The fix is to pull the toilet, replace the seal and check the flange.
Replace it if the bowl or tank is cracked, repairs keep recurring or the toilet is an older high-volume model. Toilets made before the mid-1990s can use 3.5 gallons or more per flush, while WaterSense models use 1.28 gallons or less.
If it is the only toilet or the water is rising, yes. A plunger is the safe first try. If several fixtures back up, the problem is deeper, and drain unclogging service is the right call.
Yes. Bring the model details so we can check the rough-in distance, supply connection and flange before the visit.
Use septic-safe toilet paper and never flush wipes. A toilet that keeps clogging in a septic home may point to a full tank.